House Calls with the RV Doctor
By Gary Bunzer
July 2006
Dear RV Doctor:
I have an older Hydro-Flame 19,000-Btu furnace; the serial number is 0066957. The thermostat is a Robertshaw CM60. My problem: I can’t get ignition. I have had the DSI board checked, and the technician said that it was okay. What I need to know is how I can eliminate each component one at a time, such as the thermostat. How can I wire across it to call for heat to see if it is okay? How can I eliminate the DSI board, the sail switch, the fan limit, and the solenoids on the gas valve? The instructions that came with the furnace are very vague. I have a full bottle of propane, and it’s hooked up with a very short hose, so I have fuel. Any help will be greatly appreciated.
Charlie Hopkins
Wheeling, West Virginia
RV Doctor: Charlie, there are actually two versions of your furnace, though the difference involves only the flame sense circuit and does not apply directly to your question. Here’s how to test the components you mentioned.
The thermostat can be tested by eliminating it from the circuit. Remove the two wires and connect them together. If the furnace fires up, the thermostat is faulty. The circuit board can be tested only by using an approved electronic board tester, or by swapping the board with a known good one. Most RV service facilities will have the correct board tester.
The sail switch is a “normally open” switch. With the voltage disconnected, attach a volt-ohmmeter to the two terminals on the sail switch. There should be continuity measured only when the paddle of the switch is manipulated. When released, the meter should show infinity.
The limit switch is just the opposite; it’s “normally closed.” Being a thermal switch, the limit switch will open at a preset temperature. Attach the volt-ohmmeter to both contacts and carefully heat the thermal disc portion of the switch with a match. The switch should open when the disc is heated.
The board itself performs three basic functions: It sends voltage to the gas valves; it creates the spark for ignition and monitors the micro-amp remote sense circuit; and it will perform a lockout if ignition did not take place. The voltage to the board first passes through a breaker, the relay, the sail switch, and the limit switch. If the motor turns too slowly, the sail switch will not close and voltage will never reach the board. This is common when the squirrel cage becomes heavily laden with dust and lint. The extra weight slows the revolutions to the point that the sail switch won’t even close. If you have voltage present at the gas valve while the fan is turning, then the relay, the sail switch, and the limit switch are all okay.
On some early Hydro-Flame units, there is an additional on-off switch located between the board and the gas valve. If this switch is turned off, the gas valve will never open. If the fan does not operate at all, it could be the relay or the fan motor. If the fan runs, the board is activated, and no spark occurs, but there is voltage at the gas valve, chances are the board is faulty. Check the ground connection carefully and be sure you have a fully charged battery in place. Low voltage can cause a plethora of additional problems as well.
Antsy Antenna
Dear RV Doctor:
I have trouble with a Winegard crank-up TV antenna. It seems to continue to work loose where it travels through the roof of my motorhome. I have had it tightened three times and had the main section replaced once. I still have the problem. Any suggestions?
Gerry Sudman
Henderson, Tennessee
RV Doctor: Gerry, you didn’t mention the model number of your Winegard or the brand of your motorhome, but many such problems are caused by insufficient blocking support inside the roof cavity of the RV. There is usually no problem associated with solid-roof RVs. With a soft roof, the antenna must be installed next to a rafter for support. In those instances when it is impossible or impractical to do so, insert a piece of 5/8-inch plywood, 18 inches by 18 inches square, between the mounting plate of the antenna and the roof. Have the plywood straddle two adjacent rafters. Secure the plywood to the roof first and be sure to carefully seal against water intrusion. Then, install the antenna to the plywood support piece. This will distribute the stress of raising and lowering the antenna to both rafters equally. Also, be sure the gears on the antenna are lubed periodically.